A “2.36 inch SS304 welded wire mesh panel” describes a panel made from 304 stainless steel wire, with “2.36 inch” identifying a dimension that must be confirmed before ordering. It may refer to the clear opening, wire spacing measured center to center, or another dimension on a drawing. If it means the mesh opening, 2.36 in converts to 59.944 mm, or approximately 59.9 mm. Buyers should confirm the measurement method and specify wire diameter, panel size, and tolerances to obtain a quote that matches the intended application.
Click here to get more.
This guide is intended for procurement teams, engineers, fabricators, and distributors sourcing welded stainless steel mesh panels for commercial or industrial projects. It is useful when a drawing, bill of materials, or supplier description includes the phrase “2.36 inch” but does not fully define the mesh. The goal is to help buyers turn that short description into a clear, comparable purchasing specification. It does not replace project drawings or application-specific engineering review.
Mesh opening is the open distance between adjacent wires, while wire spacing is commonly described as a center-to-center measurement. The wire diameter affects the difference between these measurements, so the terms should not be used interchangeably. If the drawing only states “2.36 inch mesh,” ask the designer or supplier to identify the intended dimension in writing. A measurement sketch can remove ambiguity before production begins.
For unit conversion, 1 in equals 25.4 mm, making 2.36 in equal to 59.944 mm. A buyer may round this to approximately 59.9 mm for discussion, but the purchase specification should state the agreed nominal value and applicable tolerance. Do not assume that a converted number defines the acceptable production range. If the opening is function-critical, provide the measurement method and tolerance on the order document.
SS304 generally refers to 304 stainless steel, a commonly specified stainless grade for fabricated products. Its suitability depends on the actual service environment, including exposure to chemicals, salts, moisture, temperature, and cleaning agents. A grade name alone does not establish that the panel will perform in every corrosive or hygienic environment. Where material traceability or compliance documentation is required, state the document requirements before placing the order.
A complete request for quotation should define more than material and opening size. At minimum, include the mesh dimension, wire diameter, panel dimensions, edge finish, quantity, and intended use. Add tolerances, flatness requirements, or other inspection criteria where they matter to assembly or performance. This detail gives suppliers a consistent basis for pricing and helps buyers compare like-for-like offers.
| Specification item | What to define | Why it matters |
|---|---|---|
| Mesh dimension | Clear opening or center-to-center spacing; nominal value and tolerance | Prevents different interpretations of “2.36 inch” |
| Wire diameter | Nominal diameter in mm or another agreed unit | Affects open area, panel weight, rigidity, and fit |
| Panel size | Width and length, with units and tolerances | Determines coverage, handling, and installation requirements |
| Material | SS304 or the exact grade required by the project | Supports consistent sourcing and document review |
| Finish and edges | As-welded or other requested finish; trimmed, framed, or exposed edges | Influences handling, installation, and downstream fabrication |
Welded wire mesh panels are used in applications such as partitions, protective guards, racks, enclosures, and screening assemblies. Whether a 2.36 in opening is appropriate depends on what must pass through the mesh, what must be retained, and how the panel will be supported. A relatively open mesh may suit applications where visibility or airflow is important, but it may not provide the separation or small-particle retention required for another task. Confirm the functional requirement with the project team rather than choosing by opening size alone.
Panel performance depends on the combination of wire diameter, opening, panel dimensions, welds, and support arrangement. A large panel or a panel carrying a load may need different wire and framing details than a small, non-load-bearing guard. Do not treat mesh opening as a strength rating, and do not infer a load capacity without an applicable design or test basis. For structural or safety-related uses, provide the support layout and required load criteria for engineering review.
Shunqiang Wire Mesh are exported all over the world and different industries with quality first. Our belief is to provide our customers with more and better high value-added products. Let's create a better future together.
Also consider where and how the panel will be installed. Outdoor exposure, washdown, chemical contact, and contact with dissimilar metals can affect material selection and detailing. SS304 may be suitable for many general applications, but buyers should verify compatibility with the specific environment. If conditions are uncertain, request a material review before finalizing the grade.
Mark “clear opening” or “center-to-center spacing” on the drawing or inquiry. State the unit and whether the dimension is nominal or subject to a tolerance. If you are working from a sample, provide a drawing or measurement record rather than relying only on a verbal description. Confirm that the supplier is quoting the same interpretation.
Choose the wire diameter and finished panel width and length based on the design, support, handling, and installation requirements. For a quotation exercise only, a buyer might ask suppliers to price an example panel measuring 1,000 × 2,000 mm with 2.0 mm wire; these are illustrative request values, not a universal standard or recommendation. Replace them with the dimensions approved for your project. Include any cutouts, framing, or edge preparation on the drawing.
Specify what will be checked on delivery, such as material identification, dimensions, appearance, and packaging condition. Agree on any required documents and inspection points before production, since availability and scope should be confirmed with the supplier. Request written confirmation of the production schedule, minimum order quantity, and shipping arrangement for your order. These commercial details can vary with panel dimensions, quantity, customization, and destination.
There is no single price or lead time that applies to every 2.36 inch SS304 welded wire mesh panel. Cost can depend on wire diameter, panel size, order quantity, material requirements, finishing, packing, and freight arrangements. Minimum order quantities may also differ according to whether the panel uses standard production dimensions or requires a custom setup. Provide the complete specification and delivery destination when requesting a quotation so the supplier can respond against the same scope.
When comparing offers, check whether the quoted opening definition, grade, wire diameter, panel dimensions, tolerances, and finish match your request. A lower unit price may not represent the same product if one quotation excludes fabrication, special packing, or required documentation. Ask suppliers to list exclusions and assumptions in writing. This makes technical and commercial comparisons more useful.
At Shunqiang Wire Mesh, we work with buyers sourcing stainless steel welded wire mesh panels and can review the details of an inquiry before quotation. Send us the required opening definition, wire diameter, panel dimensions, grade, quantity, finish, and delivery destination. If you have a drawing or reference sample, include it so the requested construction can be discussed more precisely. We can then confirm the specification and commercial details available for your order.
A 2.36 inch SS304 welded wire mesh panel can be specified accurately only after confirming what the 2.36 in measurement represents and defining the remaining panel details. Treat 59.944 mm as a unit conversion, not as a complete manufacturing specification, and state the agreed tolerance and measurement method. Next, match wire diameter, panel size, edge condition, and material to the intended application, then request a written quotation with delivery and documentation requirements. Contact Shunqiang Wire Mesh with your drawing or complete specification to discuss a suitable supply option.
Are you interested in learning more about 2.36 inch ss304 welded wire mesh panel? Contact us today to secure an expert consultation!